Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Gate Repair in Hurst, TX | Vance Gate Repair Bedford
If your Ghost Controls opener is reversing for no reason, creeping at the hinge, or refusing to close in Hurst, the problem is usually not what you think. We provide independent Ghost Controls service across Hurst, and if you need Gate Repair in Hurst, the single biggest factor in local failures is the clay under your gate posts. Most callers assume a bad board or motor, but in Hurst, phantom obstruction faults on Ghost Controls systems almost always trace back to post heave from Blackland Prairie clay shifting with the seasons. Call us at (817) 572-8590 and we’ll name what we found, name what it costs, and name what we left behind.
Our techs carry the full Ghost Controls diagnostic flowcharts and service the current AXDP and TSS1 lines plus legacy models, so we can isolate board, arm, and limit-switch faults without guessing. Vance Gate Repair Bedford is an independent Ghost Controls service provider, not manufacturer-affiliated or authorized. We work on whatever opener is already on your gate, and we price the repair in writing before anyone picks up a tool.
Why Hurst Residents Choose Us for Ghost Controls Service
Adrian Vance founded this company in 2014 after years of commercial access-control work, and he runs a crew that treats a residential Ghost Controls opener with the same documentation discipline he learned on commercial entry systems. Every Hurst job leaves you with a photographed record of what was found, what was adjusted, and what was installed. That matters when you own a Gate that heaves with the clay every spring and fall, because the second technician to touch your opener should not have to rediscover what the first one already fixed.
Hurst homeowners call us because we do not steer them toward replacement when a board swap or post reset will do, though we also offer our Gate Installation in Hurst when replacement is truly needed. We install genuine Ghost Controls parts when the opener is under five years old, and we keep a working inventory of Ghost Controls control boards, arm assemblies, bushings, and receiver modules ready for same-day installs across Hurst. A live person answers the phone 24/7, and the flat price is handed to you in writing before any work starts.
We also bring a detail most gate companies skip: we write down the limit-switch readings, the arm geometry, and the part numbers we installed. That record belongs to you, not to our file cabinet. Under Clause 4 of the Haven Standard, every Hurst visit includes photographic evidence at no additional charge.
Common Ghost Controls Gate Repair Problems We Solve in Hurst
- Phantom obstruction faults from post heave. Hurst’s Blackland Prairie clay expands and contracts with rainfall, and 4×4 wood posts set 18 to 24 inches deep heave up and tilt as the soil moves. A Ghost Controls AXDP arm mounted to a post that has drifted out of plumb triggers the safety stop even when nothing is in the path. We reset and reinforce the post, then re-run the travel learn cycle so the opener stops fighting the geometry.
- Master/slave communication loss on dual-leaf gates. On Hurst ranch homes with double driveway gates running a Ghost Controls AXDP, clay shift racks the arm brackets on one leaf, and the master board loses sync with the slave board. One leaf creeps or stops entirely. We re-bush the arm clevis pins, re-align both brackets, and re-pair the boards instead of condemning the opener.
- Burned relays on TSS1 boards from Hurst ice-storm frost misalignment. When February ice racks a Hurst gate out of square, the TSS1 board detects repeated obstruction and the relay overworks to the point of failure. We replace the board with a genuine Ghost Controls unit and address the underlying freeze-thaw alignment so the new relay does not burn out the same way next winter.
- Limit-switch drift from post lean on legacy TDS2 openers. Older Hurst gates with TDS2 touch-screen systems often lean just enough to alter travel distance by half an inch, and the opener reacts by constantly reversing. After we re-set the posts or shim the hinges, we dial in the limit switches and photograph the new position.
- Battery backup failure after North Texas summers in the heat. Ghost Controls AC/DC units keep a battery in a control box that bakes in 100°F-plus heat on Hurst garage walls and gate piers. Batteries fail silently, so the backup dies right before an ice storm knocks out power. We test battery health on every Hurst service call and replace them before they strand your gate open.
BeforeAfterGhost Controls Service in Hurst: What Local Conditions Mean for Your Equipment
Hurst’s residential neighborhoods were built almost entirely between the 1950s and 1980s on North Texas Blackland Prairie expansive clay, and those original gate posts were typically set without the deep footings current code requires. Around neighborhoods like the ones off Norwood Drive, a dry summer will pull moisture out of the clay and shrink it enough that a 4×4 post can heave up to an inch, pulling the Ghost Controls arm bracket out of alignment and triggering phantom obstruction faults that owners mistake for opener failure. This is the single most common Ghost Controls repair call in Hurst, and it is a soil problem wearing a hardware costume. When the arm geometry changes by even a fraction of an inch, the limit switches and safety logic interpret the misalignment as an obstruction, and the opener reverses or refuses to move. We dig and reset the posts below the active soil layer, machine local reinforcement plates where the original holes have wallowed out, and then re-run the Ghost Controls travel learn cycle. The fix that lasts in Hurst starts with the post, not the circuit board.
Ghost Controls Models & Products We Service in Hurst
We service the current Ghost Controls AXDP (Automatic Dual Gate Opener with Departure), TSS1 (Touch Screen Single Gate Opener), and TDS2 (Touch Screen Dual Gate Opener) lines, plus legacy VKP1 and VKP2 keypad controllers. If your opener is under five years old, we install genuine Ghost Controls control boards and arm assemblies. On older legacy VKP and TDS2 units, we often retrofit a current Ghost Controls board with new harnesses instead of charging for a full opener replacement. For gates with bent brackets or elongated bolt holes from Hurst clay movement, we machine reinforcement plates locally and re-bush the clevis pins rather than replacing the gate itself. That keeps Hurst hardware in service for the practical life of the opener.
Ghost Controls Service Pricing in Hurst
Most Ghost Controls repair calls in Hurst fall into a predictable range: a service visit with diagnosis and adjustment typically runs $95 to $185; a control board replacement on a TSS1 or TDS2 opener usually lands between $260 and $440 depending on the board revision; and a full post reset with re-hanging and arm re-alignment runs $380 to $650 per post when the original footing has failed. The exact price is written down and handed to you before any work starts, so you never face an invoice larger than the quote. Call (817) 572-8590 for a free estimate on your Hurst Ghost Controls repair, and we will tell you what we found and what it costs, in plain dollars.
Serving Hurst, TX - Our Local Coverage Area
We’re based in the Hurst area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Ghost Controls Gate Repair in Hurst
The post holding your arm bracket has likely heaved or tilted as the clay dried and shrank, shifting the arm geometry far enough to trip the Ghost Controls obstruction detection. We reset the post below the active soil layer and re-run the learn cycle, which usually clears the phantom fault. Call (817) 572-8590 for a written diagnosis.
Yes, and we usually find the root cause is a gate that racks out of square from alley vibration, forcing the relay to cycle against constant obstruction detection. We replace the board with a genuine Ghost Controls unit and correct the hinge or post problem at the same time, so the new relay does not fail the same way.
A healthy Ghost Controls AC/DC battery handles a Hurst ice storm fine, but the battery fails quietly when it sits through Texas summer heat inside a metal control box. We test battery health on every Hurst call and replace dead cells before the storm season starts, so the opener works when the grid does not.
The limit switches usually are not damaged, but they drift out of calibration as the post moves. If your gate opens short of full travel or reverses at the wrong point, the limit position no longer matches the opener’s saved travel distance. We re-set and photograph the new positions, usually on the same Hurst visit.
Not necessarily. The receiver is usually fine; the antenna position and the metal content of the alley environment are the real culprits. We relocate or reorient the Ghost Controls receiver antenna, test the range from the exact approach angle you use, and confirm it opens from the alley before we leave. Call (817) 572-8590 for a free estimate on the visit.
Service Areas Near Hurst
We run Ghost Controls service across Hurst and the surrounding HEB area, including Ghost Controls service in Euless, Ghost Controls service in Bedford, Colleyville, North Richland Hills, and Grapevine. If your gate sits on the same shifting clay, we likely cover your block. See our full Hurst service area, or review our broader Ghost Controls sales & service page for model-specific details.
Book Your Ghost Controls Service in Hurst Today
Your Ghost Controls opener wants to work. The gate post under it just may not be holding up its end. Call (817) 572-8590, and a live person will get you scheduled, with a written price before we start. Same-day Hurst visits are available when the truck is close.
Written by Adrian Vance, Owner at Vance Gate Repair Bedford, serving Hurst since 2014.