Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Repair for Bedford Homeowners
A gate that won’t open, drags on the ground, or screams when it moves is a problem you want diagnosed and priced the same day. Most gate repairs in Bedford run between $180 and $650 depending on what failed, and we give you a written price before any tool touches the gate. Vance Gate Repair Bedford has repaired over 22,000 gates since Adrian Vance started the company in 2014, and we answer the phone live 24 hours a day at (817) 572-8590.
We don’t quote over the phone and hope it sticks. We come out, find the fault, write down the number, and you decide before we do the work. That’s the way it should work, and it’s the way it’s worked here since day one.
What Our Gate Repair Service Includes
Gate repair covers a lot of ground in Bedford, from the electronics that tell the gate when to move to the steel that holds it up. Here’s what we actually do when you call us for a gate that’s misbehaving.
Electric Gate Repair
When a gate has power but won’t respond, the fault is almost always in the control board, the photo-eye, or a limit switch that’s drifted out of position. We test each component with a meter, identify the failed part by name, and show you what we found before replacing anything. Most Electric Gate Repair jobs in Bedford are completed the same visit because we keep common boards, capacitors, and safety sensors on the van.
Automatic Gate Repair
Automatic Gate Repair covers problems in three places: the operator, the wiring, or the mechanical hardware that carries the gate’s weight. We’ve worked on nine major automation brands, and our technicians service whatever motor is already mounted on the property instead of pushing you toward a replacement that might not be necessary. If the issue is a worn capacitor or a loose terminal, we tell you that and fix it rather than selling you a new opener.
Hinge & Post Repair
Bedford soil shifts with the seasons, and that movement shows up first in gate hinges and posts. A gate that scrapes the ground on the latch side usually has a post leaning a few degrees out of plumb, not a bent gate. We reset posts in concrete where needed, replace seized or broken hinges, and photograph the new alignment before we leave. Hinge & Post Repair is our standard fix for this type of damage.
Gate Realignment
A gate that sags or binds is working against its own hardware, which wears out motors and tears up hinges faster than anything else. Gate Realignment means checking the hinge point, the post, and the gate’s weight distribution, then correcting what’s actually pulling it out of line. When we finish, we record the gap measurements at the latch and hinge sides so any future drift is documented and measurable.
Lock Repair
Gates take a beating from weather and daily use, and locks fail in predictable ways: key cylinders seize, maglocks lose contact, or deadbolts stop aligning with their strike plates. We repair and replace gate locks on site, including electronic locks tied into access control systems. Every lock repair gets tested five times before we call it done.
Weld & Rust Repair
North Texas heat and occasional ice storms put real stress on welded seams, especially at hinge mounts and corners. We weld cracks, reinforce fatigued joints, and grind out rust before it compromises the structural integrity of the gate. Our technicians carry portable welding rigs on the truck, so most weld repairs happen on your property without hauling the gate to a shop.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Repair
We service DoorKing operators on a regular basis, and most of the failures we see on those units come from limit-switch drift on older circuit boards. Our technicians read the manufacturer’s service manual instead of guessing, and we record the exact switch position we set so the next service call starts with documentation, not a memory.
Ghost Controls and Mighty Mule show up on a lot of Bedford driveway gates, and both brands have known failure points that we’ve learned to check first. On a Mighty Mule, it’s often a battery that’s no longer holding charge. On a Ghost Controls unit, the control box terminals corrode over time and need cleaning or replacement. Elite and LiftMaster operators round out the common residential and light commercial motors we see, and we keep OEM parts for all of these brands stocked on our trucks. Whether you have one of these or any other make, we can diagnose and repair what’s already on the property.
BeforeAfterSigns You Need Gate Repair Right Now
- The gate stops halfway and reverses. This usually means the safety sensor is misaligned or the force setting has drifted too low. Left alone, it’ll get worse, and it also means the gate isn’t closing securely at night.
- You hear grinding or squealing when the gate moves. That’s metal on metal, typically at the hinge point or the drive gear. Every cycle of that sound is removing material from something that costs more to replace than to fix now.
- The gate scrapes the ground or won’t latch. A sagging gate is a structural issue that puts extra load on the motor. The longer it runs out of alignment, the more parts it damages, including the operator itself.
- The keypad or remote works intermittently. Intermittent faults are often a failing capacitor or a corroded connection in the control box. It works when it wants to, but it’s already failed, it just hasn’t failed permanently yet.
- The gate opens on its own or won’t fully close. This can be a limit switch problem or a receiver picking up stray signals. Either way, a gate that behaves unpredictably is a liability, especially if you have kids, pets, or a pool behind it.
Our Gate Repair Process - Step by Step
- 1
Diagnosis, documented. We arrive, you show us what the gate is doing, and we start testing. We check voltage, switch positions, wiring continuity, and mechanical alignment, and we take photos of what we find. A photo-eye misaligned by two inches gets photographed before and after correction.
- 2
Written price before work. You get a flat price in writing before anyone picks up a tool. The Haven Standard Clause 1 is simple: have it in writing. No “we’ll see how it goes” pricing, no surprise at the end. You approve the number first.
- 3
The repair itself. Our technician replaces the failed part, resets the limit switches, or welds the broken seam, then tests the gate through full cycles under load. We don’t just make it move, we make it right and verify it.
- 4
Documented photo record. Before we leave, you get a photographic log of what was found, what was adjusted, and what was installed, along with the part number. This goes in your hands and in our job file. If a future technician ever needs it, the record is there.
- 5
365-Day Done Right Promise. If the repair isn’t right within a full year, we come back and make it right at no charge. No argument, no fee, no expiration within that window. That’s the standard every Vance Gate Repair job is held to.
How Much Does Gate Repair Cost in Bedford?
A typical gate repair in Bedford runs between $180 and $650, depending on the failure. Here’s how the common jobs break down:
- Limit switch adjustment or replacement: $180-$280
- Photo-eye realignment or replacement: $180-$320
- Capacitor or control board replacement: $220-$550, depending on the brand and board
- Hinge replacement (per hinge, welded): $250-$450
- Post reset in concrete: $400-$650, depending on post size and access
- Weld repair at a seam or bracket: $180-$400, depending on length and position
What changes the price is the brand of motor (some control boards cost more than others), whether the post needs to be dug out and reset, and how accessible the hardware is. What shouldn’t change the price is the mood of the technician or how nice your house looks. You get a written quote before work starts, and that’s the number you pay. We also offer a free second opinion on any written estimate from another company. Bring us the paperwork and we’ll review it at no cost.
Gate Repair Near Bedford - Our Service Area
We repair gates across Bedford and the surrounding cities, including Hurst, Euless, Colleyville, North Richland Hills, Grapevine, Southlake, Keller, Irving, Arlington, Coppell, and Grand Prairie. Most Bedford repair calls are completed the same day or next morning, depending on parts availability. If you’re looking for Gate Repair in Hurst or Gate Repair in Euless, those are cities we cover with the same written-price, documented-work standard. You can also find details on our home page about how we approach every job.
Serving Bedford, TX - Our Local Coverage Area
We’re based in the Bedford area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Repair in Bedford
Gate repair is the process of diagnosing and fixing the mechanical, electrical, or structural problem that’s keeping your gate from working properly. In Bedford, that includes everything from a misaligned photo-eye on an electric gate to a broken weld on a steel driveway gate. We find the specific fault, show you what we found, and give you a written price to fix it before the work starts.
Most gate repairs in Bedford are completed in one to two hours on the first visit. Jobs that require new concrete for a post can take a second visit so the concrete can cure before the gate’s weight is applied. We’ll tell you the timeline in writing before work begins.
Most Bedford gate repairs cost between $180 and $650, depending on the part and the work involved. A limit switch adjustment runs on the lower end; a post reset in concrete runs on the higher end. Call (817) 572-8590 for an exact written quote, and our estimates are free.
Yes, we service Ghost Controls and Mighty Mule systems regularly, along with DoorKing, Elite, LiftMaster, FAAC, BFT, Linear, and Viking. We keep OEM parts in stock for the most common failures on these brands, so in many cases we complete the repair the same day. If you’ve got a different brand, we’ll diagnose it the same way, meter-first, documentation to follow.
Yes. We answer the phone live 24 hours a day, and we dispatch emergency gate repair to Bedford addresses every day of the week. If your gate is stuck open and you can’t secure your property, call us and we’ll get a technician headed your way with a written quote before work begins.
Every gate repair we complete is covered by our 365-Day Done Right Promise. If the repair isn’t right within one full year, we come back and fix it at no additional charge. No argument, no fee, no expiration during that window. You also get a documented photo record of every job so the warranty has evidence, not just a handshake.
Clear the area around the gate, move any vehicles that block full swing, and if you have a keypad or remote, have one on hand for testing. You don’t need to describe the problem perfectly, we’ll find it with the meter and the camera. If you have an old estimate from another company, bring that too, and we’ll review it free under our second-opinion offer.
Schedule Your Gate Repair Service in Bedford Today
Call (817) 572-8590 for a free estimate on gate repair in Bedford. A live person answers at any hour, and we’ll give you a written price before any work begins. No voicemail loop, no callback queue, just a straight answer and a documented job.
Written by Adrian Vance, Owner at Vance Gate Repair, serving Bedford since 2014.