Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Parts & Welding for Bedford Homeowners
Most Bedford gate failures come down to one worn or broken part: a hinge that’s seized, a post that’s leaned, a rail that’s bent, or a weld that finally let go. Since 2014, Adrian Vance and the Vance Gate Repair Bedford team have repaired over 22,000 gates, and the pattern holds. The gate itself is usually fine. The part is not. We replace and weld gate components with a written price handed to you before any work starts. If your gate drags, sags, or won’t latch, call us at (817) 572-8590. We dispatch to Bedford neighborhoods the same day for urgent repairs.
Our technicians arrive in uniform, introduce themselves by name, and document every part removed and installed with photographs. That record is yours to keep. Under Clause 4 of the Haven Standard, every visit includes a photo log of what was found, what was set, and what was installed. No other our Gate Parts & Welding in Bedford leaves that kind of paper trail on a residential job.
What Our Gate Parts & Welding Service Includes
We work on the parts that actually fail: hinges, posts, rails, rollers, latches, locks, and the welds that hold all of it together. If a part can be repaired, we repair it. If it needs replacement, we quote the part and labor in writing before the first tool comes out. Here is exactly what our Bedford gate parts and welding service covers.
Hinge Replacement
Gate hinges carry the full weight of the gate every time it swings, and in Bedford’s summer heat and spring storms, they wear unevenly. A worn hinge shows up as a gate that sags toward the latch side or scrapes the ground at the far end. We remove the old hinge, match the replacement to the gate’s weight and swing pattern, and weld or bolt it in place. You get a photo of the old hinge and the new one before we leave. The 365-Day Done Right Promise covers the replacement for a full year.
Post Replacement
A leaning post is almost never just a leaning post. It is a post that is losing its footing in the soil, and in the clay-heavy ground around Bedford, that happens faster than most homeowners expect. We cut out the failed post, set a new one in concrete at the correct depth, and plumb it before the gate goes back on. If the old post can be straightened and reinforced, we tell you that first and quote both options. You decide with written numbers in front of you.
Rail Repair
Rails are the horizontal members that give a gate its structure, and they bend when a gate is hit, forced, or simply old. A bent rail causes the gate to bind against the frame or leaves gaps that let pets through and undermine the latch alignment. We straighten rails where the metal is sound, and replace sections where it is not. Every rail repair in Bedford gets a post-repair photo showing the alignment before we call the job done.
Custom Welding
Not every gate part exists on a shelf. When a bracket cracks, a decorative scroll snaps, or a frame needs reinforcement, we fabricate the piece on-site or in-shop and weld it to match the existing steel. Adrian Vance started welding on commercial access-control sites in 2014, and that same standard applies to residential work: clean welds, correct penetration, and a photographed record of what was done. If the part can be sourced as OEM, we use the OEM part. If it cannot, we build it.
Gate Rollers
Sliding gates and cantilever gates run on rollers, and when those rollers wear flat or seize, the gate jerks, grinds, or refuses to move. We replace rollers with components rated for the gate’s weight, not whatever is cheapest at the local supply house. Bedford homes with sliding driveway gates often see roller failure after five to seven years, and the telltale sign is a gate that moves but sounds like it is dragging gravel. We replace the rollers, clean the track, and photograph the new hardware in place.
Latch & Lock
A gate that will not latch is a gate that will not stay closed, and in a neighborhood where kids and dogs are part of the landscape, that is a safety problem as much as a security problem. We repair and replace gate latches, padlock loops, drop rods, and the strike plates they catch against. If your lock is integrated with a gate opener, we check the electrical release and alignment at the same visit. The repair is quoted in writing before the work begins.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Parts & Welding
We carry and install parts for Ghost Controls, DoorKing, Elite, and Mighty Mule gate systems, among the nine automation brands we service across Bedford and surrounding cities. A Ghost Controls opener mounted on a bent rail will not last long. We check the steel under the motor, not just the motor itself, and replace brackets, arms, and mounting plates to the brand’s original spec.
DoorKing and Elite systems are common on larger Bedford properties with sliding gates, and those gates live or die by their rollers and track alignment. We have serviced hundreds of DoorKing and Elite units, and we understand what those frames require when the gate weighs half a ton. Mighty Mule systems, often found on lighter swing gates, have their own hinge and bracket wear patterns that we know well. If your gate has a different motor entirely, we still work on the gate itself. The parts and welding service does not depend on the brand.
BeforeAfterSigns You Need Gate Parts & Welding Right Now
- The gate drags or scrapes the ground. This is usually a hinge or post problem. Metal grinding against concrete gets worse by the day, and the continued scraping bends rails and stresses welds until a simple hinge replacement becomes a full frame repair.
- The gate won’t latch or stay closed. A failed latch or misaligned strike plate is not a personality quirk of an old gate. It is a part that has worn out, and every unlatched wind gust slams the gate against its stop and accelerates the damage.
- You see visible rust, cracks, or broken welds. A crack at a weld joint will spread. In Bedford’s humid spring months, an exposed crack invites corrosion into the steel, and the repair grows larger and more expensive the longer it waits.
- The gate is crooked or leaning noticeably. A leaning gate means a failing post or a bent hinge, and it shifts the entire load of the gate onto parts that were never designed to carry it alone. The longer it leans, the more parts fail.
- The gate jerks, grinds, or shudders when opening. For sliding gates, this is almost always a roller or track problem. For swing gates, it is typically a hinge that has seized or a post that has moved. Either way, the motor is working against failing metal, and the motor usually loses that fight.
Our Gate Parts & Welding Process - Step by Step
Every repair follows the same sequence, and you see the evidence at each stage. That is the Haven Standard, and it has been the operating rule at Vance Gate Repair since Adrian Vance founded the company in 2014.
- 1
We inspect and photograph the gate. The technician documents the entire gate: hinges, posts, rails, welds, rollers, and latch. You receive these photos, and they stay in the job record. This is the baseline that makes every later decision transparent.
- 2
We name the exact part and write the price. Before any work begins, you get a written scope and a written price. Not a range. Not a verbal estimate. A specific number for the specific parts and labor required. Under Haven Standard Clause 1, this is non-negotiable.
- 3
We do the work, documenting as we go. Parts come out, new parts go in, welds are made, and everything is photographed. If we find something unexpected, we stop and show it to you. The price does not change without your written approval.
- 4
We test the gate under real use. The gate opens and closes multiple times, the latch is checked, the alignment is verified, and limit switches on automated gates are read and recorded. We write down the readings so future repairs start from data, not guesswork.
- 5
We leave you the record. You get a photo log of every part removed and installed, a written description of what was set and adjusted, and the part numbers of everything used. If any technician ever works on this gate again, they start from this record instead of rediscovering the same problem.
For any service listed on our home page, the same process applies. Whether it’s a hinge replacement or a full custom weld, you get the written price and the photo record every time.
How Much Does Gate Parts & Welding Cost in Bedford?
How much Gate Parts & Welding costs in Bedford depends on the part, the gate’s weight, and how much labor the repair requires. Here are the ranges we most often quote:
- Hinge replacement: $120-$280 per hinge, depending on gate weight and whether welding is required.
- Post replacement: $350-$750 per post, including concrete, setting, and gate re-hanging.
- Rail repair or replacement: $180-$450 per rail section, depending on length and steel gauge.
- Custom welding: $95-$300 per repair point, depending on complexity and fabrication time.
- Gate rollers: $150-$400 for a full roller set replacement on a sliding gate.
- Latch and lock repair: $95-$250, depending on whether the strike plate or keeper needs realignment or fabrication.
These are the numbers we write on the estimate before the work starts. The final invoice matches the written price unless you approve a change in writing first. That is the entire point of the Haven Standard: no surprises, no “we had to do extra work” phone calls after the fact.
What affects the price most is gate weight. A light pedestrian gate hinge costs far less than a hinge on a 700-pound steel driveway gate. Access also matters. If we cannot get a truck close or the gate is set in a tight side yard, the labor clock runs longer. You avoid overpaying by getting a specific written price, not a vague estimate, and by refusing to pay for parts you did not approve. Our free estimates in Bedford include the full photo inspection and the written scope. Call (817) 572-8590 to schedule one. We also provide a free second opinion on any written estimate from another company. Bring the paperwork and we will review it at no cost.
Gate Parts & Welding Near Bedford - Our Service Area
We perform gate parts and welding work across Bedford and the surrounding area, including Hurst, Euless, Colleyville, North Richland Hills, Grapevine, Southlake, Keller, Irving, Arlington, Coppell, and Grand Prairie. Most urgent repairs in Bedford are reached the same day. For specifics on our work in neighboring cities, see Gate Parts & Welding in Hurst and Gate Parts & Welding in Euless. If your gate is broken anywhere in the mid-cities, we will come look at it.
Serving Bedford, TX - Our Local Coverage Area
We’re based in the Bedford area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Parts & Welding in Bedford
Gate parts and welding covers the repair and replacement of the structural components that hold a gate together: hinges, posts, rails, rollers, latches, locks, and the welds connecting them. In Colleyville Gate Parts & Welding service areas like Bedford, most gate failures trace back to one of these parts rather than to the gate motor or opener. We replace worn parts with correctly rated components and weld broken or fabricated pieces back to full strength. Every repair includes a written price and a photo record.
Most hinge, roller, latch, and weld repairs are completed in two to four hours on-site. Post replacements take longer because the new post needs time to set in concrete before the gate is re-hung, typically requiring a follow-up visit the next day. We tell you the timeline in writing before the work starts. For urgent failures, our Gate Parts & Welding - Euless and Bedford calls are typically dispatched the same day.
Most single-part repairs in Bedford run between $95 and $750, depending on the part and the gate’s weight. A simple latch repair sits at the low end, while a full post replacement with concrete work sits at the high end. You get a specific written price before any work begins, not a range. Call (817) 572-8590 for a free estimate and we’ll inspect the gate in person.
Yes. We service Gates Parts & Welding for gates with Ghost Controls, DoorKing, Elite, Mighty Mule, LiftMaster, FAAC, BFT, Linear, and Viking openers. When a gate frame or hinge fails, the motor brand does not determine the repair. We match parts to the gate’s construction and the existing opener’s mounting points.
In most cases, yes. A live person answers our phone 24 hours a day, seven days a week, and we dispatch same-day for urgent Bedford repairs, including gates that will not close or secure. Call (817) 572-8590 and tell us what the gate is doing. If it is a safety issue, we prioritize the call. The written price still applies, even on emergency work.
Every repair Vance Gate Repair completes is covered by the 365-Day Done Right Promise. If the repair is not right within a full year, we make it right at no charge. No argument, no fee, no expiration within that window. The warranty covers parts and labor on work we performed, and the photo record we leave behind makes it easy to verify exactly what was done.
Clear the area around the gate on both sides so our technician can inspect the full structure, and if you have a sliding gate, make sure the track is accessible and free of debris. If your gate has an opener, locate the power disconnect if you know where it is. You do not need to provide any tools or parts. We arrive with the common replacements on the truck, and anything we need to order is quoted before we order it.
Schedule Your Gate Parts & Welding Service in Bedford Today
If your gate sags, scrapes, will not latch, or shows a crack in a weld, call Vance Gate Repair Bedford at (817) 572-8590. You will get a live person, a same-day visit for urgent work, and a written price before any repair begins. The estimate is free, the photo record is included, and the work is covered by the 365-Day Done Right Promise. We serve all of Bedford and the surrounding mid-cities.
Written by Adrian Vance, Owner at Vance Gate Repair, serving Bedford since 2014.