Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Grapevine, TX
Gate access control in Grapevine means integrating keypads, intercoms, and card readers onto gates that sit under one of the busiest flight corridors in the country. The mix here is unusual: 1970s-era subdivisions with original swing gates near Lake Grapevine, newer HOA communities on the north and west edges with ornamental iron and strict finish rules, and a resort corridor along Gaylord Trail running commercial-grade slide gates. Aircraft vibration from DFW approach paths loosens operator mounts and wiring connections faster than in quieter neighbors like Southlake, so we see callouts here that are less about a single failed part and more about cumulative loosening. If your gate won’t respond to a keypad or remote, call (817) 572-8590 and a live person answers.
Why Grapevine Homes Are Different
Grapevine’s residential gates contend with two forces most cities don’t have at the same scale. First, the flight corridors. Persistent low-frequency vibration from DFW arrivals and departures works on every threaded fastener on a gate: hinge bolts, post anchors, operator mounting plates, limit switch brackets. What starts as a quarter-turn of loosening becomes a gate that sags, an opener that binds, or a keypad that loses contact with the control board. Second, the soil. North Texas black clay swells and contracts through wet-dry cycles, tilting posts seasonally and throwing operator arms out of alignment. After a freeze event like February 2021, we see a spike in warped wooden gate frames and frozen operators across Grapevine’s older subdivisions, where original cedar gates are now 25 to 30 years old. HOA communities on the northern and western edges add another layer: finish specifications that must be matched exactly when we weld or replace hardware.
Our Main Grapevine Services
Most Grapevine homeowners reach us for one of three problems: a gate that won’t open, a gate they need built, or a motor that’s stopped responding. Each has its own page for this city.
Gate Repair in Grapevine
This covers the mechanical side: sagging gates, broken hinges, bent posts, welded cracks, rollers off track. In Grapevine, we often find the root cause is black clay soil heave tilting a post by an inch or two over two or three seasons. We straighten or replace, re-weld the stressed joint, and photograph everything before we leave. Full details live on the Gate Repair in Grapevine page.
Gate Installation in Grapevine
New builds in Grapevine’s HOA communities typically need ornamental iron with an automatic operator and finish matched to the community standard. Older lots by Lake Grapevine often replace original cedar with steel or aluminum. The job starts with a written scope and price, not a verbal estimate. See the Gate Installation in Grapevine page for what’s included.
Gate Motor & Opener in Grapevine
When a LiftMaster or FAAC operator in Grapevine stops mid-travel or fails to respond, it’s often a limit switch that’s drifted out of position through repeated vibration cycles. We service nine automation brands, so we repair the motor you have rather than steering you toward replacement. The Gate Motor & Opener in Grapevine page walks through common failures and pricing.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Grapevine
Gate access control in Grapevine means the electronics that decide who gets through: keypads, remotes, phone entry, card readers, and video intercoms. In this city, the work often lands on gates that have been through years of DFW flight-corridor vibration, so wiring terminals and antenna connections have worked loose even when the gate itself is sound. Repair usually starts with re-seating connections and testing signal, not replacing the board. This is the same documentation habit we bring to every Gate Access Control job: photographed readings, a written part number, a record you keep.
Keypad Entry
Signs you need it
The keypad lights but won’t trigger the gate, or it works intermittently after rain.
What it costs in Grapevine
Keypad replacement or re-wiring in Grapevine typically runs $190 to $420 depending on whether the control board is involved.
How we do it
We test the keypad’s output at the control board, replace the unit or re-terminal the wiring, and photograph the final connection.
Video Intercom
Signs you need it
The video feed is black, the call button doesn’t ring inside, or the gate release from the intercom is unreliable.
What it costs in Grapevine
Video intercom repair in Grapevine runs $340 to $820 depending on whether we’re replacing the outdoor station, the indoor monitor, or both.
How we do it
We verify power and communication wiring at both ends, replace the failed component, and leave a written record of every setting.
Phone Entry
Signs you need it
The gate calls the house but the touch-tone open doesn’t fire, or the dialer never connects.
What it costs in Grapevine
Phone entry repair in Grapevine typically runs $260 to $550, with the high end involving a failed cellular module.
How we do it
We check the dialer, signal strength, and relay output, then replace the bad part and document the fix.
What Gate Access Control Costs in Grapevine
| Item | Typical range in Grapevine |
|---|---|
| Keypad replacement | $190 - $420 |
| Video intercom repair | $340 - $820 |
| Phone entry repair | $260 - $550 |
How long does a keypad repair take in Grapevine?
Most keypad repairs are done in one visit, usually 60 to 90 minutes. If the wiring has been damaged by vibration from the flight corridor, we may need a second visit to run new conductors. Call (817) 572-8590 to schedule.
Can you add video intercom to an existing Grapevine gate?
Yes. We install video intercoms on existing operators from LiftMaster, FAAC, and other brands without replacing the motor. The price is written before work starts and the estimate is free.
Gate Parts & Welding in Grapevine
Gate parts and welding in Grapevine covers the physical failures: hinges that have broken under soil-driven post movement, posts tilted by black clay, cracked welds on ornamental iron, rollers worn flat. On older Grapevine gates, especially original cedar and steel from the 1980s and 1990s, the metal is often repairable even when the geometry has shifted. We weld, reinforce, and replace parts rather than pushing a full gate swap. Every job leaves with a photo log and a written part record, the same standard we document under Gate Parts & Welding on every ticket.
Hinge Replacement
Signs you need it
The gate scrapes at the latch side, the hinge pin is visibly worn, or the gate drops when it swings.
What it costs in Grapevine
Hinge replacement in Grapevine typically runs $160 to $380 per pair depending on gate weight and whether welding is needed.
How we do it
We support the gate, cut or unbolt the old hinges, weld or bolt the new pair, and photograph the alignment.
Post Replacement
Signs you need it
The post leans visibly, the gate binds seasonally, or the post base is cracked around the concrete footer.
What it costs in Grapevine
A replacement post in Grapevine’s black clay runs $480 to $1,100 including a deeper concrete footing to resist heave.
How we do it
We remove the old post, dig a deeper footing, set the new post, and document the plumb measurement before re-hanging the gate.
Rail Repair
Signs you need it
A top or bottom rail is cracked at a weld point, the gate sags in the middle, or the rail shows rust-through.
What it costs in Grapevine
Rail repair in Grapevine typically runs $180 to $420 depending on the crack length and whether we’re splicing or replacing the rail.
How we do it
We notch the damaged section, weld in a matching replacement, grind the bead flush, and photograph the finished joint.
What Gate Parts & Welding Costs in Grapevine
| Item | Typical range in Grapevine |
|---|---|
| Hinge replacement | $160 - $380 |
| Post replacement | $480 - $1,100 |
| Rail repair | $180 - $420 |
Can you weld a cracked ornamental iron gate in Grapevine?
Yes, and that’s often the smarter repair than replacing the gate. We weld the crack, reinforce the backside if stress is concentrated, and leave you a photo of the completed joint. Call (817) 572-8590 for a written price.
Do you replace posts that have tilted from Grapevine’s soil movement?
Yes. Tilted posts are one of our most common Grapevine callouts because the clay here heaves so aggressively. We set replacement posts on deeper footings and document the plumb line after the concrete cures.
Brands We Service in Grapevine
We service nine gate automation brands including LiftMaster, FAAC, Elite, and Mighty Mule. Common parts for these Grapevine-area gates are stocked on our trucks, which keeps most repairs to one visit. See our brands for the full list.
Pricing for Gate Repair in Grapevine, TX
| Service | Typical range in Grapevine |
|---|---|
| Keypad replacement | $190 - $420 |
| Video intercom repair | $340 - $820 |
| Phone entry repair | $260 - $550 |
| Hinge replacement | $160 - $380 |
| Post replacement | $480 - $1,100 |
| Rail repair | $180 - $420 |
| Gate motor/opener repair | $220 - $650 |
| Full gate installation | $2,800 - $12,000 |
What pushes a Grapevine price toward the top of the range is usually soil damage, not the part itself: a post that needs a deeper footing, a rail that’s stress-cracked from vibration, or wiring that’s been loosened over years of flight-corridor traffic. Every price is written and handed to you before any work starts, and that number doesn’t change unless you approve a change in scope.
Neighborhoods We Serve in Grapevine
We work across all of Grapevine, from the established subdivisions around Lake Grapevine and historic downtown to the newer HOA communities on the north and west sides, and the commercial gates along the Gaylord Trail corridor. Response time for most Grapevine calls is same day or next morning.
- Stonebridge Crossing
- Fairways of Timarron
- Lakeview Estates
- Heritage on the Lake
- Pecan Hollow
Service Area - Cities Near Grapevine
Grapevine sits at a point where our crews reach several neighboring cities quickly. We also serve Southlake, TX, Colleyville, TX, Euless, TX, and Coppell, TX with the same written-price and photo-record standard.
Serving Grapevine, TX - Our Local Coverage Area
We’re based in the Grapevine area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Grapevine
Yes. Our crews run local routes through Grapevine and the surrounding DFW corridor daily. Emergency calls are answered by a live person 24/7, and we give you a name and photo before the technician arrives.
Many Grapevine communities, especially newer master-planned developments, have finish specifications that must be matched exactly. We work to those specs and can provide the written scope and photo documentation your HOA likely wants before and after the job.
Yes. The slide gates and access-control integrations on that corridor are a large part of Grapevine’s gate repair demand. We stock commercial-grade parts and understand the code requirements for pedestrian safety edges and photo-eyes on high-traffic gates.
If your Grapevine gate won’t open, won’t close, or won’t respond to the keypad, call (817) 572-8590. A live person answers, and your written estimate is free.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Grapevine Customers Say
"Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C.