Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Dallas
Gate repair in Dallas usually means one of two things: an automatic operator that won’t move, or a heavy swing gate that no longer lines up with its latch. Most repairs in this city run $215 to $640 for hinge and alignment work, and $380 to $950 when the motor or control board needs replacement. Those are the numbers we hand you in writing before any work starts, because we work under a rule called the Haven Standard and Clause 1 says the price goes on paper first. If your gate is down right now, call (817) 572-8590 and a live person answers, day or night.
We know Dallas gates because we work on them every week, from the wrought-iron driveway entrances in Preston Hollow to the newer slide gates in master-planned communities up toward the LBJ corridor. The soil here is the deciding factor in most repairs, and we’ll get to that. First, know this: you’re not calling a handyman who “also does gates.” You’re calling a company that has repaired over 22,000 gates since 2014 and leaves you a photo record of every adjustment and every part number before we pull out of the driveway.
Why Vance Gate Repair Bedford Is Dallas’s Preferred Gate Repair Company
Most gate companies in Dallas will give you a verbal estimate and a handshake. We give you a written scope, a written price, and a documented record of what we found, what we changed, and what we installed. That’s not a marketing line; it’s how the company has operated since Adrian Vance started it out of commercial access-control work in 2014. The same wiring-diagram habit that keeps a commercial site’s gate log clean gets applied to your residential driveway gate, every visit.
Dallas homeowners call us after they’ve already been burned once: a technician reset travel limits, collected a service fee, and the gate jammed again eight weeks later. The problem was never the limits. It was the post that heaved out of plumb on Blackland Prairie clay. We re-plumb the post, photograph the footing, and set the operator to match the new geometry. Then we hand you the photo log. That’s Clause 4 of the Haven Standard, and there’s no extra charge for it.
Key takeaways:
- Written price in your hand before any tool touches the gate
- 365-Day Done Right Promise: if it’s not right within a year, we make it right, no argument
- Background-checked, uniformed technicians with name and photo sent before arrival
- Free second opinion on any written estimate from another Dallas gate company
- Live person answers the phone 24/7, no voicemail loop
Our Gate Repair Services in Dallas
Electric Gate Repair
Electric gate repair in Dallas typically runs $250 to $620, depending on whether the issue is the control board, a bad capacitor, or a motor drawing too much current. The brutal part of Dallas summers is thermal stress: control boards mounted inside metal operator housings cook in weeks of 100°F heat, and solder joints and relays give out years earlier than the same board would in a milder climate. We service nine automation brands, so we don’t steer you toward replacing a good motor just because we don’t stock the part. If a Ghost Controls board has failed, we repair it. If a DoorKing operator is serviceable, we service it.
Automatic Gate Repair
When an automatic gate stops responding in Dallas, we start with the operator’s error codes and work backward to the mechanical cause. We don’t clear force errors and leave. A LiftMaster operator throwing repeated force faults on a Preston Hollow swing gate is usually telling you the gate itself is binding, not that the motor is weak. We measure the post plumb, check hinge wear, and recalibrate travel only after the steel is moving freely again. That sequence is why our repairs hold through the next season instead of repeating in six weeks.
Hinge & Post Repair
Hinge and post repair may be the single most important service we perform in Dallas. The city sits on Blackland Prairie expansive clay, which swells when wet and shrinks when dry. That movement heaves gate posts out of plumb by inches over a single season. The hinge was never the original problem; the hinge is just the part that screams first when the post leans. We re-plumb posts, set them on properly compacted footings, weld or replace worn hinge collars, and document the before and after with photos and measurements so you can see what moved. This work typically runs $340 to $880 in Dallas, depending on post size and whether welding is required.
Gate Realignment
A gate that “sagged on one side” in Dallas is almost never a worn hinge alone. It’s the near post that has heaved after a summer drought, and resetting the operator’s travel limits without fixing the post just pushes the problem down the road. Our realignment process starts with a plumb check on both posts, then we shim or reset as needed, and only then do we adjust the gate leaf and the latch. If we find the post has moved, we tell you before we touch anything, with a written price for the fix. No surprises at the end of the job.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Dallas
We work on nine major gate-automation brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That breadth matters in Dallas because the housing stock runs the full range from 1980s FAAC and BFT operators in Preston Hollow and Devonshire to newer Ghost Controls and Mighty Mule units going into far North Dallas communities. We carry parts for all of them and we know which control boards have been discontinued and need retrofitting. If an Elite operator is dead and the board is obsolete, we’ll show you the retrofit path with modern safety photocells and explain the cost difference before you decide. We repair first, replace only when it’s the cheaper honest answer.
Common Gate Repair Problems We See in Dallas Homes
- Climate-driven gate shifting: The wet spring-to-dry summer cycle on Blackland clay heaves posts seasonally, so a gate that latched in March can bind at the latch in August. The fix is re-plumbing the post, not shimming the hinge.
- 1980s-era control board failures: Older FAAC and BFT boards in North Dallas estates push past 100°F internally during summer heat waves, causing cold solder joints and dead operators. Retrofitting to a modern board with current-sensing and photo-eye support costs more up front than a band-aid relay swap, but it means no second call next summer.
- Post-2021 freeze damage: Winter Storm Uri taught this city something about sub-zero embrittlement: PVC conduit to gate motors cracked in hundreds of homes, and latches snapped when gates tried to cycle while frozen. Hard freezes now trigger a wave of calls for conduit replacement, latch replacement, and hydraulic operator seals. We stock the parts before the next forecast drops.
- Safety photo-eye retrofits: Many gates installed before 2001 in Dallas have no photo-eye beam. We recommend retrofitting all of them, especially on any gate that can close on a child or a vehicle. It’s a $180 to $380 add-on and the retrofit brings the gate closer to modern safety practice.
Here’s the field vignette that tells you how we actually work, not a scripted version. In Preston Hollow, we reset a twisted wrought-iron driveway swing gate where the near post had heaved two inches after a summer drought. The LiftMaster operator threw repeated force errors. We re-plumbed the post footing, cold-welded a cracked hinge post collar, and recalibrated the travel limits. That was a one-visit fix. It hasn’t missed a cycle since, and the homeowner has the photos proving what was wrong.
Pricing for Gate Repair in Dallas, TX
Here are the ranges we quote in Dallas, before any work begins:
- Diagnostic visit (applied to repair): $85 to $125
- Hinge replacement (single gate, steel or wrought iron): $215 to $420
- Post re-plumb / footing reset: $340 to $880 depending on post size and concrete work
- Gate realignment: $180 to $390
- Control board replacement or retrofit: $380 to $950 including parts
- Full automatic operator replacement: $1,200 to $3,400 depending on brand, gate weight, and whether safety edges or photocells are already present
Every price is quoted and agreed in writing before any work starts. That’s Clause 1 of the Haven Standard, and it means the number on the invoice matches the number on the quote you already approved. If we find something else while we’re in there, we stop, photograph it, bring it to you, and hand you a written price for the additional work. You decide. We don’t decide for you and bill you after.
Call (817) 572-8590 for a free estimate on any of the above. We’ll give you the written number over the phone or in person before you commit to anything.
We Also Serve Cities Near Dallas
Our Gate Repair team runs Dallas jobs daily, and the same documented process applies whether we’re working in Irving, Grand Prairie, Coppell, or Euless. If you’re in one of those nearby cities, the same black clay soil and the same summer heat are working against your gate. Our Gate Repair in Dallas service area covers the whole metro, with dispatch coordinated from our Dallas-Fort Worth office so we can reach most properties quickly. Free estimates apply everywhere we go.
Serving Dallas, TX - Our Local Coverage Area
We’re based in the Dallas area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Dallas
The sag usually means the post itself has heaved out of plumb on Blackland Prairie clay, not that the hinge is worn. When Dallas dry spells shrink the soil around the post footing, the post leans, and the gate sags with it. We re-plumb the post and set the footing properly, then replace or weld the hinge collar if it’s been damaged by the lean. Call (817) 572-8590 and we’ll give you a written diagnosis and price.
Most 1990s gate operators can be repaired if the motor spins and the gearbox isn’t destroyed, but the control board is often the weak point, especially on older FAAC and BFT units that have baked through two decades of Dallas summers. We’ll tell you the honest line between repair and replacement: if the board is obsolete and the motor ends are worn past tolerance, replacement is often cheaper than chasing serial failures. We show you the numbers for both paths in writing before you choose.
After a hard freeze in Dallas, the usual culprits are a cracked PVC conduit that let moisture in and shorted the operator, a snap in the latch mechanism from sub-zero embrittlement, or a hydraulic operator seal that failed when the cold thickened the fluid. We inspect the full run, replace what failed, and photograph everything. Most post-freeze slide gate repairs in Dallas run $280 to $720 depending on what actually broke. Call for the exact number on your gate.
Yes, and we strongly recommend retrofitting them. A 1980s swing gate in Dallas was installed before modern safety standards, and if it closes on someone, the operator doesn’t know to stop. We install photo-eyes (the infrared beam that stops the gate if anything crosses the path) as a retrofit for $180 to $380 per gate, usually in the same visit as any other repair. It’s the correct upgrade for a gate that’s been in the ground 30-plus years.
We re-plumb the post that has moved, compact the footing properly, and only then realign the gate and recalibrate the operator. The short version: the clay moves your post, we put it back and set the operator to match the new, correct geometry. If you skip the post step and only shim the hinge, you’ll be calling again by August. Call (817) 572-8590 and we’ll hand you a written price for the full fix before we start.
Contact Vance Gate Repair Bedford for Gate Repair in Dallas
If your gate is down, binding, or throwing errors, call (817) 572-8590 now. A live person answers, 24 hours a day, seven days a week. We’ll ask what the gate is doing, schedule a diagnostic, and hand you a written price before any work starts. No call-for-a-quote games, no surprise invoice at the end. Just a documented repair by a technician who leaves you the photos, the part numbers, and the measurements from the job. That’s how every single one of our Dallas repairs has worked since 2014.
Written by Adrian Vance, Owner at Vance Gate Repair Bedford, serving Dallas with documented gate repair since 2014.
Gate Repair in Nearby Areas
