Gate Repair in Keller - Fixed Today, No Surprise Invoice

Gate Repair in Keller, TX

Gate access control in Keller usually means retrofitting an ornamental iron driveway gate built in the 1990s or early 2000s, when master-planned subdivisions like Hidden Lakes and Marshall Ridge made automatic gates a near-standard feature. We work on the access systems attached to those gates every week: keypads, remotes, phone entry, card readers, and video intercoms. Call (817) 572-8590 and a live person answers, any hour.

Call (817) 572-8590

Why Keller Homes Are Different

Keller’s housing stock was built out primarily between 1993 and 2012, and a large share of those homes sit on generous lots with dual-leaf swing gates on long driveways. The density of ornamental iron automatic gates here is higher than in almost any neighboring city. That matters for access control because the electronics were typically installed at the same time as the gate, which means the keypads, receivers, and intercoms now failing across Keller are mostly 20 to 30 years old.

The other factor is soil. Keller sits on clay that shrinks in drought and heaves when wet, a shrink-swell cycle strong enough to shift gate posts and pull footings out of plumb. When a post moves even an inch, the gate leaf drifts, the latch misaligns, and the access system’s sensors stop reading correctly. A keypad that “stopped working” in August is often just a gate that drifted far enough to break the lock’s contact. The repair means addressing both the electronics and the geometry underneath them.

Our Main Keller Services

Keller homeowners call us most often about three things: a gate that stopped opening, a gate that needs replacing, and a motor that is past its useful life. Here is what each job involves in Keller specifically.

Gate Repair in Keller

Most repair calls in Keller involve a dual-leaf swing gate that has drifted on clay soil or a slide gate dragging on worn rollers. We level the leaves, reset the limits, and photograph every adjustment before we leave. Written price first, always. Gate Repair in Keller

Gate Installation in Keller

New installations in Keller often replace a 25-year-old ornamental gate with a modern dual-leaf swing on a reinforced footing, sized for the long driveways common in Hidden Lakes and Marshall Ridge. We quote the full scope in writing before any work begins. Gate Installation in Keller

Gate Motor & Opener in Keller

Operators installed during Keller’s 1990s and 2000s buildout are reaching end of life simultaneously, and many are failing under the summer heat expansion that binds an uncalibrated arm. We service nine brands and never steer toward replacement when a recalibration or board swap fixes the problem. Gate Motor & Opener in Keller

Before

After

Gate Access Control in Keller

Access control in Keller means retrofitting the keypad, intercom, card reader, or phone-entry system on a gate that was probably installed when the house was built, often 25 years ago. The defining Keller issue is drift: clay soil moves the posts seasonally, and the access hardware mounted on the post moves with it. A keypad that reads fine in May can stop releasing the lock by September because the gate leaf has shifted just far enough to bind the strike. We reset the geometry first, then verify the electronics. That sequence saves Keller homeowners from replacing a keypad that was never the problem. Our Gate Access Control work always ends with a written record of what was found and what was set.

Keypad Entry

Signs you need it

The keypad works intermittently, or the code stopped releasing the lock after the gate shifted on its posts.

What it costs in Keller

Replacing a stand-alone residential keypad in Keller typically runs $250-$600, installed.

How we do it

We test the keypad at the board, meter the wiring back to the operator, and replace the unit if the fault is confirmed there, not at the gate geometry.

Phone Entry

Signs you need it

Callers ring the house but the gate will not release, or the unit works from the handset but not from the driveway.

What it costs in Keller

Cellular and internet phone-entry systems in Keller commonly run $500-$1,200 installed, depending on the panel and whether a cellular bridge is needed.

How we do it

We identify the failed component, replace it, reprogram the directory, and photograph the new settings in the job record.

What Gate Access Control Costs in Keller

Can you program an existing keypad instead of replacing it?

Often yes. If the keypad powers up and meters correctly, we reprogram codes and verify the strike releases before recommending any replacement. Call (817) 572-8590 with the model number for a straight answer.

Will a new access system work with my existing operator?

In most Keller homes, yes. We interface new access components with LiftMaster, FAAC, Elite, and most other operators already on the property. We will not sell you an operator you do not need.

Gate Parts & Welding in Keller

Gate parts and welding in Keller usually come down to metal fatigue and soil movement. The ornamental iron gates installed across Keller’s 1990s and 2000s subdivisions are now 20 to 30 years old, and the combination of summer heat expansion and clay shrink-swell cycles has pulled hinges out of alignment, cracked welds at stress points, and worn slide rails unevenly. We replace the part or re-weld the section, then document what was installed. That written record is standard on every job, under Clause 4 of our Haven Standard. Our Gate Parts & Welding work covers the frame, the hardware, and the moving parts in one visit.

Hinge Replacement

Signs you need it

The gate leaf sags, drags on the driveway, or the hinge pins show visible wear and rust.

What it costs in Keller

Hinge replacement on a dual-leaf Keller gate typically runs $150-$500 per hinge, depending on the weight of the leaf.

How we do it

We support the leaf, cut or unbolt the failed hinge, install the new one, and re-level the gate before photographing the final position.

Post Replacement

Signs you need it

A gate post has leaned visibly, the gate no longer latches, or you can see cracking in the concrete footing.

What it costs in Keller

Post replacement in Keller usually runs $500-$1,500, depending on the footing depth and whether the post carries automation.

How we do it

We cut the post free, set a new one in a deeper footing, and re-hang the gate before recalibrating the operator limits.

What Gate Parts & Welding Costs in Keller

Can you weld ornamental iron without replacing the whole gate?

Yes. Most cracked welds on Keller’s ornamental gates can be ground, re-welded, and painted to match. We will tell you if the section is too fatigued to hold.

Will my gate need new posts after the soil shifts?

Not always. We measure the post lean first. If it is under tolerance, we can often shim and re-set the hinges. If the footing has cracked, post replacement is the only honest fix. Call (817) 572-8590 for an assessment.

Brands We Service in Keller

We work on LiftMaster, FAAC, Elite, and Mighty Mule gates across Keller, among others. We stock common boards, remotes, and photo-eyes locally, which shortens turnaround on most repairs. See our brands for the full list of what we service and the parts we keep on hand.

Pricing for Gate Repair in Keller, TX

Neighborhoods We Serve in Keller

We work throughout Keller, including the larger estate-style subdivisions where ornamental drive gates are standard. Here are a few of the areas we serve most often:

• Hidden Lakes
• Marshall Ridge
• Willis Creek
• Bellemead
• Fossil Creek

Response time across Keller for repair calls is typically same-day or next-morning.

Service Area - Cities Near Keller

We serve Keller and the surrounding Tarrant County cities. If your gate is in North Richland Hills, TX, Southlake, TX, Colleyville, TX, or Hurst, TX, the same written-price policy applies and a live person answers the phone around the clock.

FAQs About Gate Repair in Keller